DC POWER SUPPLY, DC Power Supply, SUNSHINE
Sunshine Power Supply P-1505TDRated 0 out of 5(0)
- This DC stabilized switching power supply is designed for use in a Laboratories, school, production lines and electronic repair.
- It has a small size and lightweight, which is very easy to transport and carry.
- It has high efficiency, high load capacity, and low noise and is superior to liner power supplies.
- The voltage is in high stability and the ripple noise is in low level. It is designed with protection from the short circuit and over current.
- It is equipped with 5V 2A USB interface for charging the electronic equipment such as phone and laptop.
- The display mode is LCD display for good look.
- There are two type voltage: 0-5V and 0-15V. When inspecting and repairing phone, you should use 0-5V for safer and better protection from the phone.
- It is designed with 5A and 0.5A two type current. And you make choice according your operation for showing current more orecisely.
DC POWER SUPPLY
Sugon 3005Rated 5.00 out of 5(1)
- 30V/5A full digital power control single
- 10mV/1mA high accuracy and resolution
- Low noise and ripple
- CV/CC given voltage and constant current mode
- Highly reliable OCP, OVP, arbitrarily set protection
- Built-in set of parameters stored
- Outputs a switch control
- Power and memory function
- Keypad lock to prevent misuse
- Intelligent temperature control fan, effectively reduce the noise
- Easy alternative to traditional digital power
- Precisely generate the required voltages and currents.
- 0-30V adjustable DC output high-precision.
- 10mV and 1mA resolution.
- Professional power supply design with intuitive operability.
- Simple and intuitive operation, fast and accurate selection of voltage and current can be realized.
- To prevent damage to the load can be set to the value of over-voltage protection and over-current protection to prevent the voltage regulator from beyond the threshold can
- The keyguard lock panel buttons to prevent undesirable results in the key test engineering
- Just press the button to recall and save area a key to bring up the user to store the data and save user settings
- Operating Conditions :
- Input voltage : 220V /110V /
- Frequency range : 50- 60Hz
- Operating temperature : 32-104 ℉ (0-40 ºC)
- Operating humidity : < 80%RH
- Storage temperature : 32-158 ℉ (0-70 ºC)
- Storage humidity : < 70%RH
Stable Voltage :
- Output Voltage Range : 0-30V Continuously adjustable
- Setup Resolution : 10 mV
- Setup Accuracy : <0.05% 20 mV
- Ripple : < 1mVRMS
- Read back Accuracy : 10 mV
- Temp. Coefficient : < 0.1% 10mV
- Read back Temp. Coefficient : < 100 ppm 10 mV
Stable Current :
- Output Current Range : 0-5A Continuously adjustable
- Setup Resolution : 1 mA
- Setup Accuracy : <0.1% 3 mA
- Ripple : < 3mARMS
- Read back Accuracy : 1 mA
- Temp. Coefficient : < 0.1% 5mA
- Read back Temp. Coefficient : < 100 ppm 5 mA
- Dimensions : 4.3 x 6.1 x 10.25 inch (110 x 156 x 260mm)
DC POWER SUPPLY, UNI-T
UNI-T UTP1306S DC Power Supply- 32V, 6ARated 0 out of 5(0)
- The UTP1306S power supply is an economical switching DC power supply with a single output.
- Voltage/current display resolution: 10mV/1mA
- Four-digit voltage and current display
- Over voltage/overcurrent/overtemperature protection
- Three groups of one-button call memory values
- Can be set Flow/overvoltage protection value
- Independent output switch
- Operation button can be locked
DC POWER SUPPLY
Gsm-Source-3005SI+Rated 0 out of 5(0)
Rated output value: 0 ~ 30V
Adjustment method: Knob adjustment
Current display: 4-digit 0.56″ LED display
Voltage display: 3-digit 0.56″ LED display
Source adjustment rate ≤0.05%+3mV
Load regulation rate ≤0.1%+5mV (rated current >5A)
Ripple noise ≤3mVrms (5Hz ~ 1MHz)
Current regulation rate Source adjustment rate ≤0.2%+3mA
Load regulation rate ≤0.2%+6mA
Ripple noise ≤3m Arms
Recovery time ≤300μs (50% load change rate, minimum load 0.5A)
Leakage current ≤1mA (test condition: input to ground 1700VAC/2s)
Insulation resistance ≥7MΩ (test condition: input to ground 500VDC/5s)
Safety protection functions: short circuit /over temperature /overload protection
Working humidity: 5%~95% non-condensing
Working environment temperature: 0 ~ 40 ° C